...

Saimaa University of Applied Sciences Technology, Lappeenranta

by user

on
Category: Documents
17

views

Report

Comments

Transcript

Saimaa University of Applied Sciences Technology, Lappeenranta
Saimaa University of Applied Sciences
Technology, Lappeenranta
Double Degree Programme in Civil and Construction Engineering
Structural Engineering
Leskina Yana
LOAD-BEARING GLASS STRUCTURES
Bachelor‘s Thesis 2010
ABSTRACT
Leskina Yana
Load-bearing glass structures, 56 pages, 3 appendices
Saimaa University of Applied Sciences, Lappeenranta
Technology, Degree Programme in Civil and Construction Engineering
Structural Engineering
Tutors: Martti Muinonen,Tero Liutu, SUAS
Supervisor: Dmitriy Kresov, Architectural workshop ―Studio 44‖
The purpose of this thesis was prove the possibility of using glass in buildings as a
load-bearing element. For centuries, its use is limited to functions such as window
glazing. In recent decades, the improvement of science and industry has allowed the
use glass as a structural element. However, the design of such structures is still
problematic.
The study was conducted at the architectural studio "Studio 44" as an example of
glass covering of courtyards in the reconstruction of the General Staff Building of
East Annex, located between the Palace Square and River Moika. Structures of
glass coating is a system of interconnected diagonal steel trusses and glass beams,
which consist of a multilayer laminated glass.
For the calculation of the glass beam a design-computer complex StructureCAD
v.11.1 was used, realizing the finite element method in the form of the method of
displacement. To confirm the calculations conducting tests was necessary. The
testing of the glass beam of the General Staff will be made at CRIBS Kucherenko
(Central Research Institute of Building Structures) in Moscow. The test models will be
scheduled on uniform and no-uniform loads.
The results of the calculations and the tests proved the possibility of using glass as a
load-bearing element, but because of the high cost of the material, the use is not
widespread. This is compounded by the lack of normative documents for the
calculations bearing glass. For each design a special certificate and confirmed tests
are required.
Keywords: load-bearing glass structure, glass covering, glass beam, structural glass
elements
CONTENTS
ABSTRACT........................................................................................................ 1
CONTENTS........................................................................................................ 2
1. INTRODUCTION............................................................................................ 4
2. GLASS COVERING OF COURTYARDS OF GENERAL STAFF BUILDING. 8
3. VARIANTS OF STRUCTURES...................................................................... 14
3.1 Standards and regulations for load-bearing glass structures……………. 15
3.2 Innovations in design and production of glass constructions……………. 18
3.3 Glass bearing structures……………………………………………………... 19
3.2.1 Production process of glass structures……...................................... 21
3.2.2 Ecological aspect………………………………………………………... 27
3.2.3 Basic data for designing the glass cover courtyards of the General
Staff Building……………………………………………………………………. 28
3.2.4 Designing........................................................................................... 30
3.2.5 Method of calculation in brief............................................................ 34
3.2.6 Calculations of glass beam................................................................ 34
3.2.7 Conclusions and references of calculation........................................ 36
3.2.8 Tests of glass load-bearing structures…........................................... 37
3.3 Metal bearing structures........................................................................... 41
3.4 Cost of project…...................................................................................... 42
4. CONCLUSIONS, EVALUATION................................................................... 43
FIGURES............................................................................................................ 48
TABLES.............................................................................................................. 49
REFERENCES.................................................................................................... 49
APPENDICES..................................................................................................... 52
Appendix 1. The list of main architects and designers……………………….. 52
Appendix 2. Site location plan………………………………………………….... 53
Appendix 3. The types of deformations of glass beams from StructureCAD.. 54
1 INTRODUCTION
The glass roof is a good looking, non-crushing ceiling with light pouring from the sky.
It provides a sense of infinite space, a sense of an open space and at the same time
a reliable roof over your head. In addition, this structure allows the efficient use of
daylight, and thus meets the requirements of energy conservation.
The basis for the construction of such roofs is a framework. Glass size for the cell
must provide maximum light transmission for security applications. Glass should not
collapse under its own weight in horizontal or slope position. Its strength should be
enough to withstand wind and snow loads, and also produced (with the use of
appliances) repairs and maintenance works on the roof.
The first example of the usage of glass as a material for bearing structures was a
glass exhibition pavilion, constructed by Glasbau Hahn, Frankfurt am Main in 1951.
The glass walls of the pavilion are crowned by a glass roof, which lies on the glass as
I-beam cross section. (Wikipedia, 2009)
Figure 1.1 Glass pavilion with steel frames in Frankfurt
But if the said pavilion served as a demonstration of the capabilities the firm, the
glass pavilion built in Badenweiler, had served the purposes of utilitarian, connecting
the two buildings. The glass panel roof of the pavilion is based on 4 glass beams with
the span of 6.2 m and with the step of 1.7 m. The beams are glued together from
three sheets of annealed glass, the inner sheet being 15 mm thick, the outer being
4
10 mm. The outer sheet has some great height, and formed the bottom of the beam
gutter attached steel cable for a partial relieve of stress in the beam, as well as
insurance in case of failure. (Wikipedia, 2010)
In contrast to the described construction glass roof over the dining room of the
Technical University (Dresden, Germany), built in 2006, does not contain steel cables
or braces for the insurance. Main beams with the span of 5.8 m connected to the
secondary specially designed cross-shaped connecting nodes of high-alloy steel.
(Technical University, 2006)
Figure 1.2 Technical University in Dresden
Beams themselves are glued together from four layers of annealed glass of aged 12
mm thick, with strength analysis included only in the two inner layers, outer layers are
there to protect the internal mechanical damage. For admission to the application of
design and tested three modules in 1:1 scale were built. The final test was to test the
residual load capacity in the damaged outer layers of the main beam. The design has
stood the test, and the deflection was 24 mm. (Makonstroy, 2009)
Another full glass building was built in 2008. It's an Art Museum in Stuttgart. In 1999,
the design of the Berlin architectural office Hascher + Jehle emerged as the winner of
an international competition. The Stuttgart natives wanted ―to create a calm, elegant
building corpus that is clearly anchored in our time.‖ In March 2002 the construction
began building. Hascher and Jehle's final design was a distinctive yet unobtrusive
architectural gem which blends in well with Stuttgart's overall inner-city architecture.
(Kunstmuseum, 2010)
5
Figure 1.3 Kunstmuseum in Stuttgart
Visible from a distance, the glass cube encloses a stone cube that contains around
one-fifth of the exhibition floor space. The far greater part of the 5,000 square meters,
however, is located below the Kleinen Schossplatz (Small Castle Square).
(Kunstmuseum, 2010)
Figure 1.4 Preliminary sketch of museum
The new building that is home to Stuttgart‘s Art Museum consists of an above-ground
glass cube and extensive exhibition areas housed in the fully renovated underground
tunnels originally built in the sixties. The sides of the glass cube are 28.8 m in length
and 26 m in height. Its roof can be partially opened and is supported by a grillage of
girders. The glass walls are suspended from the roof girders. The load-bearing
structure of the cube facade consists of glass fins. This design solution means the
6
building envelope achieves an extremely high degree of dematerialization and offers
an undisturbed view of the heart of the town from inside the building. (Werner S.)
Figure 1.5 Fragment of glass roof
On the basis of world experience in designing structural glass, the architectural
workshop "Studio 44" under the leadership of Nikita Yavein was offered the version
of covering the translucent structures of yards of The East Wing of The General Staff
Building, reconstructed at the museum and exhibition complex of the Hermitage. The
ideology of the reconstruction is to restore enfilade constructs (suite of rooms),
baroque perspective, hanging gardens and large exhibition halls, illuminated by
skylight. The basic principle of constructing display rooms of the General Staff
Building was decided to make a suite of rooms. First, this principle derives from the
historical of the architect Carlo Rossi plans: a building consisting of separate
enfilades. Secondly, it should be universal for the exhibition halls of the Hermitage
complex: the Old, the New Hermitage and the Winter Palace.
7
Figure 1.6 Location of the East Annex of the General Staff Building
Most of the permanent exposition will be located in the enfilades (suite of rooms),
encircling the perimeter of the complex. Large-scale temporary exhibitions will be
held in the courtyard spaces. To do this, five courtyards are overlapped with glass
roofs and converted into large new enfilades. It is an alternation of large exhibition
halls, embedded in cross-body on the second floor and with hanging gardens on the
platforms. This enfilade is not straight, but tapering, converging in perspective, that
multiplies its retracts the funnel effect, originally founded in the planning of the
building whose courtyard spaces are subject to the principle of perspective
convergence. (Explanatory note of the project, 2008)
8
2. GLASS COVERING OF COURTYARDS OF GENERAL STAFF BUILDING
The General Staff Building was designed by a Russian architect of an Italian origin
named Carlo Rossi and built in 1820-1830. The main façades are facing The Palace
Square and the Moika river embankment in the immediate vicinity of Nevskiy
prospect (avenue) in the historical centre of St. Petersburg (Appendix 2). There are
five floors and five spacious courtyards in the building. (Explanatory note of project,
2008)
Figure 2.1 City the plan of General Staff Building
Originally, the Eastern Annex, which has been assigned to the State Hermitage
Museum by now, accommodated Ministry of Finance, Ministry of Foreign Affairs and
some other ministries of the Russian Empire. Since 1917 the building has been
occupied by various institutions and organisations. (Wikipedia, 2010)
The General Staff Building is a landmark of federal significance registered under
№108 and is located within the boundaries of the protection area for historical and
cultural landmarks (TSN 30-306-2002 Saint-Petersburg). (Explanatory note of the
project, 2008)
9
Figure 2.2 The facades of General Staff Building
The facades of the General Staff and its historic interiors are subject to thorough
restoration and changes are unacceptable. However, the composition and the
character of the premises differ sharply from that required of a modern museum. In
terms of functional and spatial organization of the East Wing of the General Staff it‘s
comparable to the zone of mixed uses of the quarter of courtyards with household
courtyards, combining a single façade outside. It is necessary to highlight the many
complex constructions inside the building that are integrating it into a coherent whole
with the spaces of the palace and the museum complex of the Hermitage and the
images of the St. Petersburg area. (Explanatory note of the project, 2008)
In the course of field and archival research a comparative analysis of the General
Staff and other parts of the Hermitage complex, measuring, observing and sketching,
architects (Appendix 1 ‖List of main architects and designers‖) came to the
conclusion that in the construction of buildings a number of principles, analogies and
associations, whose development will be reconstructed without violating the idea of
Rossi and turned in use in the General Staff Building in the organic continuation of
the Hermitage spaces need to be taken into use. These principles are as follows:
 The idea of baroque perspective;
 The principle of enfilade (suite of rooms);
 The structure of Hermitage hanging gardens;
 «New Large Gaps» - Hermitage exhibition halls in the transverse yard
building. (Explanatory note of the project 2008)
10
Figure 2.3 The idea of baroque perspective
Each of these principles are mentioned in a separate section of the project concept,
but they are all united in the idea of the New Grand Enfilade and specified in the
proposals for the organization of functional flows and museum trails vary in the
hierarchy of display spaces complemented by the architectural decisions of the top
natural light. And each of the sections of the project concept aims to preserve the
monument and to find a new, but not exogenous growth from within. (Explanatory
note of the project, 2008)
The architectural reconstruction project of East Annex of General Staff Building
provides a covering of existing internal yards by translucent structures. Structures of
such coverings represent the system of spatial diagonal steel trusses, which are
basing on internal building walls. As internal yards have the complex geometrical
forms on the plan, and also their sizes are different, the supporting trusses have
various distances and they have different height in different yards.
11
Figure 2.4 The cross-section of courtyard
The step of supporting trusses is 6.2 meters. On the purlin, with the help of spiders, a
double glazed window is stacked with a slope to the trusses, which create the top
translucent covering. For the leaning of the overlap, on the internal walls steel trusses
and binding beams are put, which allocate the load on the brick piers. All metal
structures are protected by fire-protection compounds for the accomplishment the
necessary fire resistance level (60 min). (Explanatory note of the project, 2008)
Figure 2.5 The building site of Eastern Annex of General Staff Building
Designs coatings households represent a system of nine (for the 5th of court), and
four (for the 4th of the yard) steel trusses, located between the buildings and
12
enclosures resting on reinforced belt, made along the edges of the internal walls of
courtyards, metal spacing of beams, the decoupling form with each other .
Figure 2.6 Longitudinal section of courtyards №5 and 4
The maximum span of the trusses is no more than 39 m, the step installation trusses
being 6.2 m. To the top chord at the intersections of bracing with a step 1.7 m, fixed
bearing glass beams, which are the basis for supporting the glass elements of the
roof. (Explanatory note of the project, 2008)
Figure 2.7 The cross-section of courtyard №5
In one of the supporting units support conditions on the reinforced concrete
structures a truss belt using fluoroplastic gaskets is arranged to slide the bearing.
13
Figure 2.8 The fragment of glass covering
Drainage trays, devices of heating and block systems for the hoisting of exhibits are
located in the coupled trusses. The beams are hanged to the lower belts of trusses,
catwalks for the washing of translucent structures moving along the beams. Fire
safety is provided by fire sprinkler system (the entire length of the glass beams on
both sides are dispensers). Smoke is removed through transom in the last beams.
(Explanatory note of the project, 2008)
14
3 VARIANTS OF STRUCTURES
The usage of glass as a building material has a long tradition because of
transparency. Its primary usage for windows led to the fact that existing standards
and regulations are primarily determined by the requirements of relevance in this
area. Unfortunately, the standards also have a lot of noticeable flaws. All this leads to
the unsatisfactory situation, which has various negative consequences. In Russia the
situation is complicated by the lack of any documentation for load-bearing glass.
Doubts about the correctness of design and the lack of generally accepted methods
of calculation are often time consuming and expensive due to laboratory tests. On
the other hand, large load-bearing glass structures are unsatisfactory from an
economic and architectural point of view and small sized are unacceptable from a
security perspective.
As a result, the basic requirements for the design of glass load-bearing structures
are:
1. Durability, which requires:
 Comprehensive and clear decision for the to structure.
 Accuracy, flexibility and scope to match the current structures.
 Options of structures must comply with only one physical aspect and not be
dependent on test conditions. When hazardous scenarios in case of damage
to the surface, the main danger to the load-bearing element should be based
not on the load, but should be on the defective of the surface.
2. For a better understanding of the design tests must be conducted (in order to
obtain meaningful and sustainable results.)
3. The main risk in respect of load-bearing glass structures will be discussed
and resolved.
4. Safety (calculation of structures in light snow and wind loads);
5. Thermal insulation (calculation of structures subject to specified heat transfer
coefficient of resistance);
6. Smoke system (number and type of smoke elements);
7. Internal drainage of condensate;
8. Removal of moisture from the outer surface of structure;
15
9. Sealing and insulation places adjacency to the elements of structural;
10. Acoustic permeability;
11. Design heating in the winter time.
3.1 Standards and regulations for load-bearing glass structures
Written standards need to be taken into consideration together with research, design
and construction experience when a new construction project is started. However,
they tend to lag behind the advanced research and new construction projects. With
this in mind, it is not surprising that there are shortcomings in the standards and
guidelines for the design of glass in construction. Construction under the direction of
these regulations is increasing, but still not yet at a level with other construction
materials. Design guidelines and standards such as the IStructE on constructive
glass (IStructE: Structural use of glass in buildings) and a project document for
engineers IABSE's on the glass (Structural use of glass, Structural Engineering
document no. 10) is very small and rare and they require regular updating to keep
pace with the rapid development of science. Designing legal instruments is still in its
infancy, architects and designers have more freedom to develop glass structures and
this inevitably leads to the fact that there is a lot of variety in the differences of the
calculation of load-bearing glass structures. (IStructE, 1999; IABSE, 2008)
Standards vary in detail and complexity, ranging from the development of charts in
some countries to more detailed guide calculations in other countries. None of the
existing standards do not provide the basic parameters for calculating the loadbearing glass, which are necessary for the development of new designs. In addition,
there is a lack of comprehensive standards for the manufacture of glass, and its
characteristics, such as laminating and thermal hardening, which lead to significant
changes in the field of quality control.
There is a perception that it is necessary to develop a single international standard
for the load-bearing glass. However, this standard will only provide consistent basic
properties and methods in the calculation of glass structures, not excluding the
alternative, supported by tests. For nearly 10 years an instrument for glass design
16
was being developed, but this standard has faced some difficulties. Recently, the
European Commission has developed a Eurocode for load-bearing glass. The
commission has yet to approve this proposal, it‘s currently discussing the project and
a negative response will, of course, be a big blow to the construction community
working with glass.
The American National Standard ‗Standard Practice for Determining Load
Resistance of Glass in Buildings‘ ASTM E 1300-04 provides extensive charts to
determine the required thickness of glass plates. It is based on the glass failure
prediction model by Beason & Morgan and on the finite difference stress and
deflection" analysis by Vallabhan (Vallabhan, 1983). Resistance is defined using a
target failure probability of 8‰. ASTM E 1300 applies to vertical and sloped glazing
in buildings exposed to a uniform lateral load and made of monolithic, laminated, or
insulating glass elements of rectangular shape with continuous lateral support along
one, two, three or four edges. The specified design loads may consist of wind load,
snow load and self-weight with a total combined magnitude less than or equal to 10
kPa. The standard does not apply to other applications such as balustrades, glass
floor panels and structural glass members or to any form of wired, patterned, etched,
sandblasted, drilled, notched or grooved glass or to any glass with surface and edge
treatments that alter the glass strength:
The verification format is with q being the uniform lateral load, LR the ‗load
resistance‘, NFL the ‗non-factored load‘ (based on a 3 s load duration) and GTF the
so-called ‗glass type factor‘ (load-duration dependent, see below). (ASTM E 1300-04,
2004)
The important difference with respect to European design methods is that this
verification format is based on loads and not on stresses. Furthermore, it does not
use any partial factors. The NFL is determined from charts given for various
geometries, support conditions, glass thicknesses and for monolithic as well as
laminated glass. The GTF combines glass type and load duration effects and is given
for single panes (Table 3.1) as well as for insulating glass units.
17
Table 3.1 Glass type factors (GTF) for a single pane of monolithic or laminated glass.
The Canadian National Standard ‗Structural Design of Glass for Buildings‘
CAN/CGSB 12.20-M89 deals with soda lime silica glass panes exposed to uniform
lateral load. Like the American National Standard, it is based on the and a target
failure probability of Pf = 0.008 for the resistance. It is important to notice that in
contrast to ASTM E 1300-04, which uses a 3s reference duration for the resistance,
CAN/CGSB 12.20-M89 is based on a 60s reference duration. This is due to the fact
that the Canadian Standard, published in 1989, is based on ASTM E 1300-94 while
the 3s reference duration was only introduced in ASTM E 1300-03. (CAN/CGSB
12.20-M89, 1989)
In the thesis, because of the lack of standards and GOSTes for the calculation of
bearing glass structures, SNIP 2.01.07-85 ―Loads and pressures‖, SNIP 23.01.1999
"Building Climatology", building codes SN 481-75 ―Instructions for the design
installation and operation of double-glazed windows‖ and Technical Regulations
―About the safety of glass and its products used in buildings‖ are used. In Russia, this
regulation is the only guide for the calculation of similar structures. The project of
technical regulations developed by the initiative group of the Expert Council for
legislative support of the development of glass industry in the Committee of State
Duma in Economic Policy of Russian Federation, entrepreneurship and tourism with
the participation of Russian enterprises for the production of glass products. This
document authorizes the use of European standards and regulations, except for
requirements that can not be used due to climatic and other peculiarities of the
Russian Federation. For each design requires a special certificate and verified tests
are requared.
18
3.2 Innovations in design and production of glass constructions
Glass objects are not limited by environmental requirements but preserve
transparency and lightness in a glass structure. At the moment with the latest
developments engineers can:
- Determine the mechanical properties of glass, in particular, the ability to predict
the strength and the variability of glass.
- Improve the quality of laminated glass, which maked it less stratifiable, longer to
use and being improved appearance.
- Develop a high-performance mechanical connection to reduce stress
concentration while enhancing the productivity of glass.
- Develop a rigid adhesives and gaskets, such as in glass Sentry Glass Plus with
pad DuPont, which enables the use of laminated glass as plywood. (DuPont
SentryGlass)
- To design large autoclave plants that will allow producing laminated glass large
3.5 m to 15 m and more than 8 m to 20 m.
- Develop a glass-metal connection, which eliminates the need for drilling holes
in the glass and reduces the stress concentration around the joints.
These innovations allow the use of glass as a load-bearing element, but despite
these successes there are some problems and obstacles for further development:
- Reduction or elimination of metal elements from glass often requires expensive
testing.
- Large glass panels are now often limited by the problems due to transport,
access and replacement.
- In most design guidelines no difference is made between key load-bearing glass
elements and secondary structures of glass.
- The large size and the importance of glass elements mean that the quality of
manufacturing and tolerances are in the foreground. Despite improvements in the
quality of lamination, there are several manufacturers and installers who can install
and laminat glass with a low tolerance of high quality production work.
- Connection type (stress concentration in the holes) still determines the type of
construction, for example, glass thickness, number of layers, type layers, etc.
19
3.3 Load-bearing glass structures
New architectural solutions offer a wide variety of applications of glass as a
constructive building material, which makes it necessary to supply the calculation of
the structural elements of glass and assessment of their carrying capacity on a new
footing. Today, there are no methods of calculating the load-bearing glass elements
described as norms and rules; in each case an application is required, supported by
a series of tests. Experiments and discussions lead to the creation of the concept of
reliability, based on which can be developed, methods of calculation and
dimensioning, as well as standards for the design, taking the necessary safety
requirements into consideration.
Glass amorphous is a substance, but also it is a durable material, due to a close
arrangement of atoms. This crystal lattice occurs during solidification of the viscous
substance in solid form, not allowing crystallizing in a regular lattice (Fig. 3.2).
Figure 3.1 Schematic image of an irregular lattice of sodium-silica glass
The glass consists of silica fused at high temperatures mainly with borates and
phosphates. Also, the glass exists in nature formed by a vulcano or meteorite
formed. Despite his irregular grid, which places the material somewhere between the
solid and the liquid phase, there is sufficient adhesion molecular structure for
mechanical strength. (K.Leitch K., 2005.)
Table 3.2 Chemical composition of soda-silica and borosilicate glass, in compliance
with the Eurocodes (EN 572-1:2004) and (EN 1748-1-1:2004).
Soda lime silica glass
Borosilicate glass
Silica sand SiO2
69 – 74%
70 – 87%
Lime (calcium oxide) CaO
5 – 14%
–
Soda Na2O
10 – 16%
0 – 8%
20
Soda lime silica glass
Borosilicate glass
Boron-oxide B2O3
–
7 – 15%
Potassium oxide K2O
–
0 – 8%
Magnesia MgO
0 – 6%
–
Alumina Al2O3
0 – 3%
0 – 8%
others
0 – 5%
0 – 8%
According to ASTM E1300-04, there are common terms for different types of glass.
Use of non-specialized titles makes glass easy to work with for design the engineers.
Table 3.3 shows the terms used in the construction.
Table 3.3 Terminology types of glass
Level of residual surface
compression
Terminology in the
present document
Other frequently used
terms
(almost) none
annealed glass (ANG)
float glass
medium
heat strengthened glass partly toughened glass
(HSG)
high
fully
annealed
(FTG)
unspecified (HSG or FTG)
heat treated glass
glass annealed glass;
(thermally)
toughened
glass
Table 3.4 Physical properties of soda-silica and borosilicate glass (EN 1748-11:2004; EN 572-1:2004).
Density
Knoop hardness

kg/m3
HK0,1/20 GPa
2500
2 200-2 500
6
4.5-6
Young‘s modulus
E
MPa
70000 60 000-70 000
Poisson‘s ratio

–
0.23
0.2
10-6 K-1
9
Class 1: 3.1-4.0
Class 2: 4.1-5.0
Class 3: 5.1-6.0
720
800
1
1
–
1.52§
01.05.10
–
0.837
0.837
Coefficient of thermal expansion
Т
cp
J kg-1 K-1
Thermal conductivity

-1
Average refractive index within the
visible spectrum
n
Emissivity (corrected)

Specific thermal capacity
21
Wm K
-1
The most important physical properties of soda-silica and borosilicate glass are listed
in Table. 3.4. One of the most important properties of glass is the chemical resistance
to aggressive environment, which explains its popularity in chemical industry and
makes glass one of the most durable materials in construction. The optical properties
depend on the thickness, chemical composition of the coating (film) of load-bearing
glass. The most obvious feature is the transparency in the wavelength range from
380 nm to 750 nm. Due to the interaction with O2 much UV is absorbed. Wavelengths
> 5000 nm locked group SiO. This is the greenhouse effect - visible light penetrates
through the glass and heats the space inside, and locked long waves on the surface
of glass. (DuPont SentryGlass)
The degree of sound insulation fireproof glass, consisting of hardened fire-resistant
glass, meets the degree of insulation of float glass the same thickness and it varies
from about 28 to 35 dB (Rw), depending on the thickness of the glass. With the help
of a thin layer of gel (about 1 mm), or the use of laminated glass with PVB film, R w
value can be increased to the level of 36-39 dB. (Chesnokov A., Zlotopolskiy A.,
2007)
Load-bearing glass has an almost perfect isotropic behavior, brittle fracture and it is
not plastic. The theoretical strength of load-bearing glass reaches almost 6,000 MPa,
and sometimes even 10,000 MPa. But as in all brittle materials, tensile strength of
load-bearing glass depends largely on surface defects, which are sometimes visible
to the naked eye, as well as the size of the elements of the nature and intensity of the
load and residual stresses. The chemical composition and physical properties of the
glass allows its use in construction as load-bearing element. With the help of modern
technology these characteristics may improve.
3.2.1 The production process of glass structures
Currently, the production of float glass is the most popular basic production
processes, and is about 90% of all flat glass in the world. The main advantages of
this manufacturing process, represented by Pilkinton brothers in 1959, is its low cost
and wide availability, superior optical quality glass and large size sheets. Mass
22
production of glass, improved over the past 50 years, has become affordable enough
to be widely used in the construction industry. Over the past two decades, advances
in glass technology have facilitated the analysis of structural methods (e.g. finite
element method), which allows the use of glass as a structural element. In the design
of glass structures laminating sheets for stock are often used in the event of a
sudden failure of one of the elements.
For the structural usage of glass hardening is the most important method of
treatment. Float glass is heated to about 620°- 675°C in the furnace and quenched
(rapid cooling) jets of cold air. This effect cools the surface, which freezes and then
freezes, and the core glass. During the first seconds, the cooling process leads to
tensile stresses on the surface and compressive inside. If the initial temperature is
too low, the relaxation can not take place and tensile stresses can cause the glass to
shatter in the oven. As soon as the surface temperature drops below 525°C, the
glass solidifies and relaxation will be terminated immediately. The temperature
distribution is approximately a parabola. Cooling leads to a characteristic residual
compressive stresses on the surface and inside the glass. For best results, the stress
state, this process should occur when the surface is hardened at a time when a
maximum difference in temperature is set weakened at the original strain. The
hardening of borosilicate glass is difficult even under high pressure air or quenching
in a liquid because of its low coefficient of thermal expansion. (Haldimann M., 2006)
Figure 3.2 The principle of tempering glass
23
The idea is to create a favorable residual stress field due to tensile stresses within
the glass and compressive near the surface. The core of the glass does not contain
defects and, therefore, has good resistance to stretching. Inevitable defects on the
surface of glass can only grow if they are subjected to tensile stress.
Breaking the scheme is a function of the energy stored in the glass, residual stresses
and stresses due to loads. As an example, Figure 3.3 shows the breakdown of the
structure of samples, loaded with a common axis of double rings. A fully tempered
glass has the highest level of residual stresses and, as a rule, divided into small,
relatively harmless fragments of about 1cm2, tempered glass is called ―safety glass‖.
Heat strengthened glass ―is a compromise between a good structural performance
and a large enough fragmentation in the split‖. Burned glass is a standard float glass
without any admission. (Haldimann M., 2006)
Figure 3.3 Comparison of the destroyed structure: baked glass (left), heat tempered
glass (middle), fully tempered glass (right).
Typical residual surface compressive stresses ranging from 80 MPa to 150 MPa for
fully calcined soda-silica glass. The most important parameter for the quenching of
the glass is the coefficient of thermal expansion of glass and heat transfer coefficient
between glass and air. In particular, the coefficient of heat transfer is difficult to
estimate, it depends on the quenching (geometry, impact bars, air pressure, air
temperature, etc.) and, therefore, varies from one manufacturer of glass to another.
(Haldimann M., 2006)
Standard thickness for fired glass is 3, 4, 6, 8, 10, 12, 15, 19 and 25 mm. Typical
maximum dimensions are of 3.0 m x 6.0 m sheet, and 3.2 m x 8.0 m, possibly even
more on special order. Burned glass may have corrosion cracking under the
24
influence of long loads. This phenomenon is due to the presence of microcracks at
the edges of the sheet under the action of water, which lengthens the cracks. There
is a threshold voltage, after which the stress-corrosion cracking is no longer a
significant factor, it is 7N/mm2. (Wilson P., Vasilchenko-Malishev G., 2006)
Another phenomenon, which affects bronzed glass, is thermal shock. Selected areas
of glass can be warmed unevenly in the sun, the temperature difference between the
surface and its main site at the junction with the frame may be 33° C. This leads to
cracking due to internal stresses resulting from temperature differences between the
two different parts of the same sheet of glass. So often, experts recommend using
windows, consisting of two components, for example, triplex and toughened glass.
("Roof" Journal, 2008)
Also, laminated glass plays an important role in structural usage. It consists of two or
more sheets of glass, bonded together by a transparent plastic layer. Glasses may
be the same or different in thickness and may also be different in the heat treatment.
Most of the lamination process is in an autoclave at a temperature of about 140°C.
The thickness of the glass depends on the duration of the load and temperature.
For the roof glazing the choice depends on the transparency requirements and safety
design in each case. Safety can be achieved in three ways: by using annealed glass,
a triplex or glass with deposited layers. The strength of annealed glass is 4 - 5 times
higher than usual because of a special heat treatment. A triplex, which is also called
laminated glass, is a kind of "sandwich" consisting of two or more sheets of ordinary
polished glass, by proper fastening together by a special layer. Such glass has a high
impact resistance, and fastened the layer does not allow it to break into fragments
during fracture. The behavior of laminated glass on impact can be seen in Fig. 3.4.
(―Roof‖ Journal, 2008)
25
Figure 3.4 The behavior of laminated glass made from various types of glass
(Sedlacek., 1999).
In the laminated glass a polyvinyl viscoelastic layer (PVB) is usually used. The
physical properties of the film depend on the temperature and duration of the load.
When damaged, the glass layer tries to keep the pieces in place, thereby reducing
the chance of injury from falling glass. A nominal thickness of PVB film is 0.38 mm. In
general two – 0.76 mm or four – 1.52 mm are used in the form of one. Heat treatment
is sometimes advisable to use up to 6. Also used transparent resin with a layer
thickness from 1mm to 4mm are sometimes used to achieve special properties, such
as soundproofing DuPont's SentryGlass Plus. The layer is blocking ultraviolet
radiation. The penetration of ultraviolet (UV) rays of the sun or fluorescent sources,
causes damage to interior fabrics, furniture and works of art. (Saint Gobains Glass;
DuPont SentryGlass)
Fire protection in the laminated glass is also carried out by using layers. Under the
influence of fire, glass cracks but remains in place and formes an impenetrable shield
of insulating foam.
26
Fig. 3.5 The classification of fire resistance
To ensure fire safety in the supporting structure must consist of fireproof glass must
have a the fire resistance class G30, G60, G90 and G120 with the individual
requirements of protection. According to a classification in EN 13501-2 the fire
resistance performance is expressed by letters, explaining the functional requirement
and numbers explaining the performance time in minutes (Fig. 3.5):
E: Integrity – provides a physical barrier against flame, hot gases and smoke.
EI: Integrity & insulation – provides a physical barrier against flame, hot gases
and smoke as well as a reduced surface temperature and resistance against
spontaneous ignition on the unexposed side.
EW: Provides a physical barrier against flame, hot gases and smoke and offers a
reduced heat radiation. (SCHOTT, 2010)
Glass is initially a brittle material, but the calcined glass (float) has a relatively low
tensile strength and is broken into sharp shards that represent a danger of injury.
Calcined glass can be read in conjunction with other materials for the production of
"safety glass", which has the ability to reduce the risk of injury. Heat treatment for the
production of tempered glass increases the tensile strength and changes the
fragments into smaller ones (Fig. 3.6). Such a decision would certainly be better, but
does not eliminate the problem entirely, since the weight of falling glass (albeit in the
form of small rounded fragments) is quite significant and could cause injury.(Overend
M., 2008)
27
Fig. 3.6 On the right figure - Laminated glass consisting of two sheets of tempered
glass with a layer. On the right - Laminated glass consisting of two hardened sheets.
3.2.2 Ecological aspect
Public awareness of anthropogenic CO2 emissions and the effects on climate
change has increased dramatically in the last 10 years. There is also a growing
recognition that buildings are responsible for a large proportion of CO2 emissions approximately 40% of end user CO2 emissions, where heating, cooling, ventilating
and lighting of buildings account for a third of all global CO2 emissions. In an attempt
to reduce energy demand in buildings there have been rafts of national and
international targets and regulations for energy efficient buildings.
Glazing has traditionally been regarded as a weak element in the environmental
performance of buildings, but the benefits of glazing such as the introduction of
natural light into a building and the resulting sense of wellbeing for building
occupants should not be underestimated. In addition there have been rapid
technological advances in glass leading to substantial improvements in the thermal
transmittance (U-value) and the solar heat gain coefficient (G-value) of glazing units.
The improvements are such that the frame is often the major source of thermal
bridging in a contemporary glazed façade. (Aleksandrov N., 2007)
When using special coatings, for example, SentryGlas cover LOW-E, increasing
energy efficiency in buildings. It can also help design more efficient thermal insulation
load-bearing glass and load-bearing glass from a more effective control of the
transmission of ultraviolet radiation. There is also load-bearing glass with a low heat
28
when using fillers between the layers, such as gas. To provide reliable protection
from sun and glare light is used to manage, with electric drive, blinds foil in the space
between the panes. (Saint Gobains Glass; DuPont SentryGlass, SCHOTT)
There are evident regional differences in this area. In colder climates (e.g. Northern
Europe) there are conflicting requirements of maximizing light transmittance and
minimizing heat loss. The latter is often strictly regulated. The preferred solution in
these climatic regions is to use large area glazing but with high performance glass
sometimes in conjunction with passive energy efficient systems such as natural
ventilation, double skin façades or shading devices. In warmer climates (e.g. The
Middle East region) it is impossible to have a full glass façade and achieve
performance without relying heavily on mechanical air conditioning systems.
3.2.3 Basic data for designing the glass cover courtyards of the General Staff
Building
The East Wing of the General Staff, located at The Palace Square, 6-8, letter A
(Annex 1) has the following characteristics:
- Object purpose and use: administrative non-resident building.
- Area of the plot: 15,562 sq.m.
- Climatic area – IIв (SNiP 2.01.01-82.)
- Design winter ambient temperature – - 26°С (SNiP 2.01.01-82.)
- Design snow load for region III according to SNiP 2.01.07-85* -1.8 kPa (180
kgf/m2)
- Normative wind load for area II according to SNiP 2.01.07-85* - 0.3 kPa (30
kgf/m2)
- Number of floors: 4-5, basement.
- Courtyard area: 3,600 sq.m.
- Land plot area: 15,562 sq.m.
- Volume: 242,445 cub.m.
- Importance class— 1 (SNiP 2.01.07-85*)
- Degree of fire resistance — 1 (SNiP 2.01.07-85*)
- Class of constructive fire danger — С0 (SNiP 2.01.07-85*)
29
- Climatic region — IIV (SNiP 2.01.01.-82)
- The building complex and the amount offset by households — to be heated
For the calculation of the design a computing complex StructureCAD v.11.1 was
used, realizing the method of finite element method in the form of displacements. It is
necessary to make the collection of loads on the 1-meter running:
1. Constant loads:
A. Double-glazing unit  ×  = 1,7 × 2,8; 
= 2500

3 ;  = 1,1
а) tempered glass t1=15mm
б) ordinary glass t2=8mm
в) ordinary glass t3=8mm


=  ∙ 1 + 2 + 3 ∙  ∙  ∙ 2 = 2500 ∙ 0,031 ∙ 1,7 ∙ 2,8 ∙ 2 = 737,8

 = 
∙  = 737,8 ∙ 1,1 = 811,58
 =

1,7 × 5,4 =
811,58
(1,7 ∙ 5,4) = 88,4
B. Profile Schuco:  = 1,05;  = 2700


2
3
T-profile 50 × 50 × 3;  = 1,29 ∙ 
тавр = 1,29 ∙ 2,8 = 3,6 ∙ 
Rectangular hot-rolled profile 50 × 50 × 4; А = 7,12
 = 1,528 ∙ 2,8 = 4,3 ∙ 
 = тавр +  ∙ 2 = 3,6 + 4,3 ∙ 2 = 15,4 ∙ 
 =  ∙  = 15,4 ∙ 1,05 = 16,2
 =

1,7 × 5,4 =
16,2
(1,7 ∙ 5,4) = 1,8

2
C. Stainless steel rack:  = 1,05;  = 7900
50 × 30 × 4;  = 5,482

3
 №1:  = 0,968
 №2:  = 0,815
 1 = 0,968 ∙ 7900 ∙ 0,0548 = 4,19
 2 = 0,815 ∙ 7900 ∙ 0,0548 = 3,53


=  1 +  2 ∙ 2 = 4,19 + 3,53 ∙ 2 = 15,43
30

 = 
∙  = 15,43 ∙ 1,05 = 16,2
 =

1,7 × 5,4 =
16,2
(1,7 ∙ 5,4) = 1,8

2
D. Glass beam:  = 5380;  = 1,1; с = 2500

3
 = 12 ∙ 4 = 48 = 0,048
 = 600 = 0,6


=  ∙  ∙  ∙  = 5,38 ∙ 0,048 ∙ 0,6 ∙ 2500 = 387,36

 = 
∙  = 387,36 ∙ 1,1 = 426,1
 =

426,1
=
5,38 = 79,2

2
Total:  =  +  +  +  = 88,4 + 1,8 + 1,8 + 79,2 =
171,2

2
2. Temporary loads:
A. Snow load:
III snow district; 0 = 180

2
B. Engineering load: 50

2
Total:  =  +  = 180 + 50 = 230

2
The total load on 1m2:
 =  +  = 171,2 + 230 = 401,2

2
3.2.4 Designing
Perpendicular to the trusses are fixed beams, made of thick laminated glass. Step
beams are 1,700 mm. Welded steel beams are fastened the square profile, which is
based in glazing, creating a translucent top fence. Double-glazed windows are
31
placed at an angle to the beams with spiders and different height-resistant steel
profiles. (Explanatory note of the project, 2008)
Fig. 3.7 3D model of glass roof
The ordinary supports beams are made of tubular steel truss structures. The span of
ordinary beam is 5,380 mm. The height of the beam – 600 mm.
Fig. 3.8 Overall scheme of the beam B1
A beam is a package of four sheets of tempered glass with a thickness of t = 12 mm,
bonded together by a point attachment type «Rodan» (Fig. 3.8).
32
Fig. 3.9 Fastening junctions of glass covering to racks
Steel racks are cross 50x50x4 mm. The scheme of attaching glass components to a
metal pendant is shown in Fig. 3.9. A pair of glass with metal parts go through a strip
of polymer material HILTI HIT-Y70 with the elastic modulus E = 1750 MPa and
compressive strength Rc = 31 MPa. Node pair beams B1 are attacheed to the points
as shown in Fig. 3.10.
Fig. 3.10 The scheme of klyammer (jointing)
33
Node interface with support beams B1 bracket as shown in Fig. 3.11. Support
brackets, made of 12 mm stainless steel band are based on the metal. (Explanatory
note of the project, 2008)
Fig. 3.11 The junction of supporting beam B1 on the steel truss
Fig. 3.12 The sections of junction of supporting beam B1 on the steel trusses
34
3.2.5 The method of calculation in brief
The calculations were performed using the design-computer complex StructureCAD
v. 11.1, realizing the finite element method in the form of the method of displacement.
The calculation is based on the method of finite elements, using nodes design
scheme with a basic unknown displacements and rotations. In connection the this the
idealization of the structures are made in a form adapted to the use of this method,
namely: the system is represented as a set of standard solid type (rods, plates,
shells, etc.), called finite elements and associated to the junctions. The type of the
finite element is defined by its geometric form, the rules determining the relation
between the the displacements of junctions of finite elements and the junctions in the
system, physic law, which determines the relationship between internal efforts and
internal displacement, and a set of parameters (stiffness) within the description of the
law, etc. (Feodosiev V., 1967)
A along with the usual kinds of influences and pressures, such as its own weight,
snow and wind, and also forced exposure (the deformation of the basement) should
be notified in the calculations. On the other hand, we should not forget about the
strength of glass, the meaning of the multilayer layer of the triplex, as well as
environmental conditions and the duration of impact loads. In this thesis the strength,
the rigidity and the stability of the series bearing glass structures (beam B1) are
analyzed. (Feodosiev V., 1967)
3.2.6 The calculation of glass beam
Diagram B1 is an ordinary glass beam with a 5.38 m length, consisting of four sheets
of tempered glass with a thickness of 12 mm. Based on the beam, there are four
racks, which hold the filler glazing. The beam is based on a stainless steel bracket. A
general view of the finite element models is presented in figures 3.13-3.14.
(Explanatory note of the project, 2008)
35
Fig. 3.13 B1. General form
Idealization geometric image was to allocate the main elements of the bearing
system of the building, the minimum simplifying their forms and ways of pairing (Fig.
3.13 and 3.14).
Fig. 3.14 B1. Fragment
Considering the following calculation loading:
№
Name of loading
L1
Estimated load on its own weight of metal elements
L2
Estimated load on its own weight of glass elements
L3
Estimated load on weight of glass covering
L4
Estimated load on engineering using
L5
Estimated load on weight of snow covering
Considering the following combination of loading:
С1= 1*(L1) + 1*(L2) + 1*(L3) + 1*(L4)
С2= С1+ 1*(L5).
36
In testing, a load transfer at the glass beam must be carried out strictly in the vertical
plane. Considering the following options applicable:
V1. The glass beam has strictly vertical position
V2. The glass beam has a deviation from the vertical plane (defects in
assembly, the strain of supporting structures, etc.)
3.2.7 Conclusions and references of the calculation
The results of the work for the triplex with a thickness of 8mm glass make the
following conclusions:
1. Maximum deflections do not exceed the maximum allowable values:
(SNiP 2.01.07-85* «Load and pressure»)
2. Overall stress-strain state
Maximum principal tensile stress is for:
Maximum principal compressive stress is for:
Local stress-strain state
A maximum principal tensile stress in the zones of stress concentration is for:
A maximum principal compressive stress in the zones of stress concentration is for:
The strength of glass panels is assessed in accordance with the theory of maximum
normal stresses. (Feodosiev V. ―Resistance materials‖) In the present with the
calculated resistance of glass is accepted as follows:
Axial tensile Axial compression Adopted criteria for general and local strength are used. The maximum utilization of
the material under tension does not exceed 0,1275 (Appendix 3).
37
Given the considerable variation in strength properties and fragile fracture of
annealed glass, as well as the incomplete of the existing regulatory base in Russia
for the design of load-bearing glass structures should provide:
- conducting mechanical tests designed glass beams cover the full size range of
the identification of their limit states for design schemes of loading and
fastening;
- computer modeling and analysis of the stress-strain state of structural
coverage in the event of local failures of elements.
3.2.8 Tests of glass beams
Estimated design is closely related to testing. The methods of calculations of glass
structures can not be discussed independently of testing procedures. In this
connection it is appropriate to introduce briefly general quality control procedures
carried out in Europe.
Static fatigue tests
Static long-term tests with constant load, which are often called ―static fatigue tests‖,
are usually carried out by loading a 4-point bending (4PB). The advantage of such
tests is that the test conditions are similar to the operating conditions of construction
elements like glass for loading a constant load, for example, its dead loads. The main
drawback of such tests - they take a long time. (Haldimann M., 2006)
Dynamic fatigue tests
The term "test on the dynamic fatigue common, is commonly used for an ongoing
testing of the load, with a constant checking of pressure and cyclic loading. Mainly by
using a 4-point bending or double rings with a single axis (CDR). The latter is also
known as concentric rings. The figure 2.21 shows the schematic drawing of the two
test systems.
38
Fig. 3.15 Schematic representation of coaxial double ring (left) and four point bending
(right) test setups. (Haldimann M., 2006)
Direct measurement of the growth of large through-thickness cracks
Particularly before measurements on indentation cracks became popular, this
experimental approach was used to determine crack velocity parameters. The growth
of a large through-thickness crack is directly measured (e. g. optically or using sound
waves) as a function of the stress intensity factor. On one hand, this is a direct and
relatively precise approach. On the other hand, however, engineers designing
structural glass elements are not interested in the behavior of
such large through-thickness cracks. (Haldimann M., 2006)
The skylight for the Yurakucho subway station for the Tokyo International Forum has
been developed by Dewhurst Macfarlane and Partners in 1996.
Fig. 3.16 Underground station of Yurakucho in Tokyo
For Yurakucho station tests were carried out at University City in London, where the
39
specimen was loaded at three points through the holes, but not on the edge. The
results showed that the average strength of tempered glass is 160 N/mm 2. From the
manual for allowable stress for short-term pressures that can be considered a safety
factor of 3. Allowable stress for tempered glass then is 53 N/mm 2. The value is quite
comparable with the characteristic values of the voltage specified in Eurocode prEN
13474-1 (in the present tense in development). (Firman Glass)
Tests for the glass failure prediction model
Forecast breakage (GFPM) does not use the aforementioned procedures. There are
two interrelated parameters of surface defects and em ~k, which are determined by
loading rectangular plates with a uniform lateral load. The growth of cracks is
determined visually and depends on the intensity factor loadings. On one hand, this
method is fairly accurate, but on the other hand, builders are not very interested in
the behavior of cracks in the thickness of glass. (Haldimann M., 2006)
In Russia, due to lack of regulations for load-bearing glass, it‘s necessary to conduct
tests. Tests for load-bearing glass beams used to cover the yards of General Staff
Building, will be organized at CRIBS Kucherenko (Central Research Institute of
Building Structures) in Moscow. A stand is designed for tests, shown in Figure 1. The
stand consists of a base (pos.1), which is established with a the vertical rack space
(pos. 2). On the vertical posts a beam (pos.3) is installed as well as a power element
designed for mounting the mobile traverse (pos.4). Moving the traverse is made at
the expense of rotational motion of elements - tenders (pos.7) is strictly on the
vertical axis through the guides. Vertical rails are installed through bush bearings.
Before the test stand is set in a horizontal position running devices (pos.5). With a
screw pair (pos.6) the facility is set in vertical position and fixed on the vertical rack
(pos. 2). (Explanatory note of the project, 2008)
40
Figure 3.17 Test sample of beam
When coupled with the rotation of tenders the test item is loaded with uniform load.
With the release of one of the tenders the test model is loaded with unevenly loads.
Working with tender communications (pos.6) are exempt and they act as guide
elements. On the rails in the upper part of the beam installed spring (pos.9) is
installed to allow shock loads in the upright position. Structural stability against
overturning tilt braces spatial supports racks (pos. 2). The test standard done on a
beam of glass span 5.38 m (fig. 3.8), consisting of 4 sheets of triplex sized 600x12
mm, connected elements - layers made of polymer material of the company «HILTI»
HIT-HY-70, 4-metal elements, bearing steel elements. (HILTI, 2009)
The test of models will be scheduled for uniform and unevenly loads. The intensity of
the estimated load is taken to be 322 kg/m2. The load will be laid in phases. After
reaching the load, endurance is needed during a day. In the process of testing a to
test system on to test the impact of shock load applied to the center of the beam in
vertical and horizontal directions. By planned checking the bearing capacity of the
test specimens the load capacity will be ensuring excess of the calculated load by
25%. (Explanatory note of the project, 2008)
To determine the parameters of the stress-strain state of a glass beam under load
values of the strains in the sections indicated on the scheme will be obtained.
Marking sensors include the section number, the number of plane glass sheet of the
41
beam, the number of sensors (sensor is 3-1-5 in section 3 on the section has the
number 2 and has №5). The placement of strain gauges are made in sections with
alleged, most normal and tangential stresses, as well as in sections with stress
concentrators. The sections with the maximum normal stresses are:
 with a uniform load - in the center of the span beams
 unevenly load - a quarter of the span beams
Sensors to determine the strain are placed on the most stressed fibers of the upper
and lower sections, on all four sheets of glass beams. Places with stress
concentrators are in the areas surrounding the holes. There are two openings in the
span zone – four in half of the beam in the reference area. To measure the strain in
sections adjacent to the openings, three sensors in 2 sheets of the beam are
installed. In the core zone and in the zone located close to a quarter of span sensors
are located on the outer glass sheets of the beam, and in areas with holes that are
closer to the center span - internal sheets. (Explanatory note of the project, 2008)
3.4 Metal load-bearing structures
The initial draft of the reconstruction of the General Staff using glass beams, but the
building is being replaced by steel trusses due to the high cost of manufacturing,
transportation and installation. Steel trusses are installed in places that the glass
beams (Fig. 3.18). (Explanatory note of project, 2008)
Figure 3.18 The plan of steel trusses
42
Standard beam length of 5,380 mm consists of curved square profiles of 50x25x4
mm and with a height of 450 mm with coated facing material on three sides.
Frameworks facing the beam are attached with the support of the transition from
metal fasteners. Supporting pattern-glazed windows and counters are done
according to the same principle as in the glass beams. (Explanatory note of the
project, 2008)
Figure 3.19 Steel truss
The design of steel trusses is calculated for strength and stability by design-computer
complex StructureCAD v.11.1, which implements the method of finite elements in the
form of displacement.
3.5 Cost of project
The reconstruction of the East Wing of the General Staff started in 2008. The first
phase of the project is financed from the federal budget (51%) and with a World Bank
loan. An estimated cost in comparison with the original will be redefined due to the
global financial crisis and the replacement of glass beams with steel trusses (an
average cost of glass beams are 4228,4 rubles per square meter). (Consolidated
construction cost estimate, 2007)
The reasons for rejecting the use of glass beams in the structures of translucent
cover the first phase of the construction are:
43
- A glass product is two or three times more expensive than similar items from
indigenous materials, due to the high cost of production and processing of
glass.
- Prices depend on several factors. The thicker the glass, the more expensive it
is.
- Frosted glass is also more transparent, even more expensive if it is toned and
colored.
- The price increases according to quenching (approximately 20%) and the
complex shape of the product: in rounded forms, it will be 10-20% more
expensive. (Glass Center, 2010)
According to the Loan Agreement, signed in July last year, the implementation of the
first phase of the project allocated 4.4 billion. According to foreman, the project has
been full of unpleasant surprises. For example, the condition of the building after the
removal of all layers of plaster was worse than expected, the windows in the building
were of one hundred and fifty sizes, almost all different from each other. All this
required additional work and increased the cost estimate compared with the original.
In the competition for the second consecutive stage five companies were involved.
Applicants for the role of general contractor of the second stage have been
prequalified. The results have been sent the World Bank to Washington. The contract
with the contractor on the results of the tender will be signed in June. The contract
price for the second stage will be higher than for the first, as more expensive
restoration work is required. According to Nikita Yavein, the amount of the contract
could reach 5.5 billion rubles. A part of the work that should have been done in the
second stage of the project, was included in the first phase. This included the
monitoring of the surrounding buildings (and the Alexander Column), as well as
strengthening the foundations of the building, the first and second, to strengthen a
separately proved risk, as they are linked (Explanatory note of the project, 2008)
44
5 CONCLUSIONS
As a constructional material the glass has been used throughout the world for more
than one millennium, but as a load-bearing element of construction it has been the
open only in the last century. In my thesis there are a few known examples of glass
as a load-bearing element, which can form the basis for the design of such
structures. Here was presented the main developments in the construction
documentation in Russia, Europe, Canada and America, which proves a great need
in the overall development of all branches of engineering, architecture, building
physics, materials science, etc. In a modern building used a variety of constructions
is used and they have their preferred areas of application in accordance with their
capabilities and features. But there are many areas in which the various
constructions vying with each other and the choice of one or the other of them is
faced by a technical and economic challenge. As for the theory of constructive forms
and the theory of structures, they are essentially the same for all building structures,
although each of them has its own characteristics.
Considering and assessing the world experience of glass designs, architectural
workshop "Studio 44" designed a version for a translucent cover structures of
courtyards of the East Wing of the General Staff Building. In my thesis translucent
cover of glass beams was calculated. With the help of this thesis one can conclude
about the use of glass structures as load-bearing elements.
In the design of any structures it‘s necessary to comply with a number of
requirements. All requirements can be divided into several groups: the purpose,
technical, technological, operational, economic and aesthetic. They are very
important. Most of them must certainly be fulfilled, primarily the purpose and
technical requirements.
The design should at its best serve its purpose, the maintenance of a process that
must take place in the projected building or a facility. For example, if it is a circus, you
need to take into account that suspended piece of equipment you need to have a
certain height and so forth, and so in each facility. Technical requirements - certainly
45
providing strength, stability (shape and location, as well as local stability) and rigidity.
These requirements are determined in a SNIP design. This is also the reliability
requirement, or, in other words, the design must work flawlessly within a
predetermined period of operation of calculation. In fact, throughout this period
strength, stability and rigidity in the light of the accumulated defects - deflections,
corrosion, etc must be provided.
The design should be technological, the should be considered to easy
manufacturing, transportation, installation. You have to think about comfort and work
performance, especially in the installation. After the design has to be mounted in heat
and severe frost. A convenience often depends on the type of connection, junctions
and other dimensions. The design should take care of the technological exploitation.
Because the design should prevent damage and corrosion. This is also included in
such a requirement as maintainability. Already at the design stage is necessary to
think about the time the design needs to be reconstructed and in some cases
strengthened. It should be borne in mind that the physical life (the actual period of its
"life"), is 3 to 7 times longer than the moral life, the period originally specified in the
process.
Economic requirements are complex - it is first necessary to save metal, to save
labor costs at all stages, to save energy costs. Hence it is important to analyze
metrics such as metal, energy and labor input. A comprehensive performance value
"in" and reduced expenditures in a market economy must not include profit. Then
they reflect the cost-effectiveness of specific structural forms. Do not forget about the
conservation requirements in the manufacture and assembly. Finally, we need to
worry about the aesthetics of design, its beauty and harmony. It should be noted that
the designed rationally design, as a rule, delights the eye with its lightness and
beauty.
At the design phase any materials should be considered in the context of the
particular design with its advantages and disadvantages. Glass is not exception to
this rule.
46
The advantages of glass:
1. The use of glass in construction work adds beauty to the building;
2. By using glass in interior, it saves the space inside the building;
3. Glass cladding in building fulfills a functional requirement of lighting, heat
retention and energy saving;
4. Using toughened glass you can get a high load-bearing capacity;
5. Glass is a good heat conductor, thereby heating the air inside the building by
solar energy. The usage of foil blinds allows to keep if naaded to completely
eliminate the heating of the building for a long time;
6. When using special layers it reduces the probability of injury from the fall of
sharp glass shards;
7. Lighting due to the large area of glazing is natural, gives significant power
savings;
8. From the psychological point of view, natural light has a positive effect on the
livelihoods and on human efficiency;
9. Tempered glass has a high fire resistance.
The disadvantages of glass:
1. Glass is a very expensive material, it may increase the budgeted cost of
construction work;
2. The usage of glass also enhances the cost of security;
3. The usage of glass increases operating costs;
4. Due to the brittleness of the material it is difficult to transport it from the place
of manufacture to the point of use;
5. The glass is also unsafe for areas prone to earthquake;
6. The lack of comprehensive data of construction documentation entails the
usage of expensive tests;
7. Possible condensation between the sheets of glazing;
8. When the temperature diffes, there may be the phenomenon of thermal
shock;
9. When using glass in covering it is necessary to remember about smoke and
fire;
47
10. The structures require high-quality work throughout the supply chain - from
the manufacturer to the builder.
After analyzing the advantages and disadvantages of glass as a load-bearing
element "Studio 44" has come to the conclusion of the possibility of using glass
coatings for courtyards of the General Staff Building. The first phase of reconstruction
of Staff Building has the aim to preserve the historical value of the building assuming
the usage of glass beams, but due to insufficient financing the decision was made to
the use steel trusses. At the moment steel is widespread used for the construction of
production facilities for heavy industries, bridges and other important buildings. This
reconstruction project was not exception, which is highly regrettable, as the General
Staff Building of the museum and exhibition complex Hermitage is a trademark of
Saint-Petersburg.
There is little doubt that the recent and future innovations in glass engineering will
improve the performance and will continue to extend the domain of what is possible.
Currently, regulatory documentation is under development, which greatly complicates
the design of load-bearing glass structures. There is a need to optimize and to bring
the documentation in compliance with the requirements of modern design. Recent
developments in societal needs and technology are creating unprecedented
challenges and opportunities in the use of glass in buildings ranging from complex
geometry to occupant safety and lightness/transparency to energy efficiency in
buildings. The challenge for design engineers and architects is to select and adopt
these technologies not as fashionable add-ons, but at an early design stage when
decisions have the largest impact on the final design, thereby leading to optimized
performance-based buildings.
48
FIGURES
Figure 1.1 Glass pavilion in Frankfurt, p. 4
Figure 1.2 Technical university in Dresden, p.5
Figure 1.3 Kunstmuseum in Stuttgart, p.6
Figure 1.4 Preliminary sketch of museum, p.6
Figure 1.5 Fragment of glass roof, p.7
Figure 1.6 Location of the East Annex of the General Staff, p.8
Figure 2.1 City plan of General Staff Building, p.9
Figure 2.2 Facades of General Staff Building, p.9
Figure 2.3 Idea of baroque perspective, p.10
Figure 2.4 Cross-section of courtyard, p.11
Figure 2.5 Building site of Eastern Annex of General Staff Building, p.12
Figure 2.6 Longitudinal section of courtyards №5 and 4, p.12
Figure 2.7 Cross-section of courtyard №5, p.13
Figure 2.8 Fragment of glass covering, p.13
Figure 3.1 Schematic image of an irregular lattice of sodium-silica glass, p.19
Figure 3.2 The principle of tempering glass, p.22
Figure 3.3 Comparison of the destroyed structure: baked glass (left), heat tempered,
p.23
Figure 3.4 The behavior of laminated glass made from various types of glass
(Sedlacek, 1999), p.25
Figure 3.5 The classification of fire resistance, p.26
Figure 3.6 On the right figure - Laminated glass consisting of two sheets of tempered
glass with a layer. On the right - Laminated glass consisting of two hardened sheets,
p.27
Figure 3.7 3D model of glass roof, p.31
49
Figure 3.8 Overall scheme of the beam B1, p.31
Figure 3.9 Fastening junctions of glass covering to racks, p.32
Figure 3.10 Scheme of klyammer (jointing), p.32
Figure 3.11 Junction of supporting beam B1 on the steel truss, p.33
Figure 3.12 Sections of junction of supporting beam B1 on the steel trusses, p.33
Figure 3.13 B1. General form, p.35
Figure 3.14 B1. Fragment, p.35
Figure 3.15 Schematic representation of coaxial double ring (left) and four point
bending (right) test setups, p.38
Figure 3.16 Underground station of Yurakucho in Tokyo, p.38
Figure 3.17 Test sample of beam, p.40
Figure 3.18 Plan of metal beams, p.41
Figure 3.19 Metal beam, p.42
TABLES
Table 3.1 Glass type factors (GTF) for a single pane of monolithic or laminated glass,
p.17
Table 3.2 Chemical composition of soda-silica and borosilicate glass, in compliance
with the Eurocodes (EN 572-1:2004) and (EN 1748-1-1:2004), p.19
Table 3.3 Terminology types of glass, p.20
Table 3.4 Physical properties of soda-silica and borosilicate glass (EN 1748-11:2004; EN 572-1:2004), p.20
REFERENCES
AGC YOUR GLASS Company. www.yourglass.com;
Aleksandrov N. Architecture of glass and metal. Publication.
http://metal4u.ru/articles/by_id/102 (Accessed on 6.2007)
ASTM E 1300-04. Standard Practice for Determining Load Resistance of Glass in
Buildings. 2004. American Society for Testing Materials.
50
Bernard F., Daudeville L., Gy R. 2002. Load bearing capacity of connections in
tempered glass structures. Publication.
Building codes SN 481-75. Instructions for the design installation and operation of
double-glazed windows. 1975. FGUP CPP, Moscow.
CAN/CGSB 12.20-M89. Structural Design of Glass for Buildings. 1989. Canadian
General Standards Board.
Chesnokov A., Zlotopolskiy A. The role of glass in security building and construction.
RIA ―Industry of safety‖. http://www.securpress.ru/issue.php?m=31&art=180
(Accessed in 2007)
Company ―Makon‖. Glass is a bearing element. Construction technology, M.
http://makonstroy.ru/forum/?p=1918 (Accessed on 18/12/2009)
Consolidated construction cost estimate (In prices of IV quarter of 2007). 2008.
―StroyConsulting‖.
DuPont™ SentryGlass. http://www2.dupont.com/DuPont_Home/en_US/index.html
Explanatory note of the project. 2008. Federal Component of the St. Petersburg
Economic Development Project.
Feodosiev V. 1967. Resistance materials, Home edition of physical and
mathematical literature. Publishing House ―Science‖.
Firman Glass. Glass Breaking New Boundaries. Publication.
http://www.firmanglass.com/breaking.html
Glass Centre. Information about glass structures. Publication.
http://www.steklocentrkaliningrad.ru/main/12-steklocentr.html
26.01.10)
(Accessed
on
Haldimann M. 2006. Fracture strength of structural glass elements – analytical and
numerical modelling, testing and design. Thesis № 3671. EPFL, Lausanne.
IStructE : Structural use of glass in buildings. 1999. Department of the Environment,
Transport and the Regions under the Partners in Technology programme.
K.Leitch K. 2005. Structural glass technology: systems and applications. Master‘s
thesis. Massachusetts Institute of Technology. Department of Civil and
Environmental Engineering.
Kunstmuseum Stuttgart, 2010 http://www.kunstmuseum-stuttgart.com/
LTD ―Perfect windows‖. Glass is a load-bearing material. Publication.
http://oknamodern.ru/100.php?c=30
51
LTD "Rubikon". Translucent covering. Design and assembly translucent
constructions.
Publication.
http://ruall.ru/content/view/40/37/
(Accessed
on
26.10.2009)
Overend M. 2008. Engineering Transparency – Current international trends in the
use of glass in buildings. Report.
"Roof" Journal. 2008. Glass roof part 1: special type of glass. Publication.
http://www.krovlirussia.ru/index.php?page=cls&hid=439&pid=794
Rumyanceva S. Interview with Vice-President Company ―Stroimontag‖ Pavlov A.
Journal "Industrial and Construction rewiew", №107.
http://www.spbpromstroy.ru/107/11.php (Accessed on marsh 2008)
SAINT-GOBAINS Glass. http://nordic.saint-gobainglass.com/b2b/default.asp?nav1=ac&LG=FR
SCHOTT Company. http://www.schott.com/english/
SCHOTT PYRAN. Special glass for integrity fire resistant glazing. Publication by
SCHOTT.
http://www.schott.com/architecture/english/download/schott_pyran_e_v0609.pdf
SNiP 2.01.07-85*. 2005. Load and pressure. FGUP CPP, Moscow.
SNIP 23.01.1999. Building Climatology. 1999. FGUP CPP, Moscow.
Structural use of glass, Structural Engineering document no. 10. 2008. International
Association for Bridge and Structural Engineering.
Technical Regulations about the safety of glass and its products used in buildings.
2010. FGUP CPP, Moscow.
TROSIFOL, 2008. Architectural glazing. PVB film for laminated. Safety glass.
Publication by TROSIFOL.
Werner S. Information about Kunstmuseum.
http://www.wernersobek.de/index.php?page=78&modaction=detail&modid=292
Wikipedia. The free encyclopedia. http://en.wikipedia.org/wiki/Main_Page
Wilson P., Vasilchenko-Malishev G. 2006. The design and construction of all glass
structures.
52
Appendix 1
1 (1)
List of main architects and designers:
1. Main architects:
Yavein N. (head of the workshop ―Studio 44‖)
Elovkov E. (main architect of the project)
2. Main disegner:
Gerchtein V. (main designer of the workshop ―Studio 44‖)
Kresov D. (main designer of the project)
3. Fire consultant:
Pechkov F. (LLC―Center fire and technical expertise‖)
4. Engineering sections:
Gyrevich A. (Company ―Petroengineering‖)
5. Manufacturer of glass beams:
Assotition ―TEMP‖
53
Appendix 2
1 (1)
54
Appendix 3
1 (2)
Deformed scheme
Deflection, mm
Form of stability loss. General form
Form of stability loss. Projection onto the plane XOY
55
2 (2)
1
3
5
2
4
6
The numbering of the holes
The principal stresses σ1, MPa
Principal stresses S3, MPa
56
Fly UP